Gr1 Titanium Wires

Gr1 Titanium Wires
Details:
Product name : Gr1 titanium wires
Size :0.1-7.0mm or as request
Diameter tolerance:±0.03~±0.05mm
Surface:bright surface /Pickled/Ground etc for option
Packing: Plastic spool with PE sealed, coil with moisture-proof film, straight bars in wooden case. MTC available
Send Inquiry
Description
Send Inquiry

Gr1 titanium wire

 

Gr1 titanium wires

Gr1 Titanium Wire (ERTi-1 / TA0)
The standard for Gr1 titanium wire is AWS A5.16 and ASTM B863. The corresponding titanium wire brand in China is TA0. As there are many types of titanium, the Gr1 grade belongs to the highest purity titanium wire among commercial pure titanium materials, with the best plasticity and toughness. Gr1 titanium wire products are mainly used as filler wires for TIG/MIG argon arc welding.

 
 
Main chemical composition of Gr1 titanium wire (mass fraction wt%)
Ti content Balance
O content  ≤ 0.18%,The main feature of Gr1 titanium wire products is that its oxygen content is strictly controlled, less than or equal to 0.18%. This is also the core distinction between Gr1 and Gr2. Therefore, the plasticity of Gr1 titanium wire is far superior to that of Gr2 wire.
Fe content ≤ 0.20%
C content ≤ 0.08%
N content ≤ 0.03%
H content ≤ 0.015%
Other impurities single ≤ 0.10%, total ≤ 0.40%
 
 
Physical and mechanical properties of Gr1 titanium wire
Products name Gr1 Titanium wire
Material density  4.51 g/cm³ 
Material Tensile strength ≥ 240 MPa
Material Yield strength ≥ 170 MPa
Elongation after fracture ≥ 24%
Elastic modulus: 103 GPa
Max shaft load 3800kg
Long-term working temperature range -253℃ ~ 300℃; short-term maximum 350℃
Melting point 1668℃
magnetic  non-magnetic
gas release rate It is very low 

Gr1 Titanium Wire Product Features 


1. The titanium in Gr1 titanium wire products is of high purity and extremely low interstitial elements. Moreover, our titanium wire products strictly control the oxygen content. Therefore, when used for welding, the weld seam has the best plasticity and toughness.


2. When using Gr1 titanium welding wire for welding, its product fluidity is very good, and the weld seam is very aesthetically pleasing. It is not prone to produce pores or brittleness.


3. After welding, using Gr1 titanium wire as the filler wire, the weld seam maintains excellent ductility, resistance to impact, and thermal shock, and is not prone to cracking.


4. The surface of Gr1 welding wire products is bright and clean, without oxide scale or oil stains. This can better reduce welding pollution.


5. The weld pass passivation film is more stable, and the corrosion resistance after welding matches the corrosion resistance of Gr1 base material.


6. Titanium material is a soft and easily bendable material, so you can choose wire coils or straight bars according to different working requirements.

 

When used with additive materials, the following suggestions are provided for the selection of titanium wires

 

 

1. Gr1 titanium wire has a weakness in strength, especially the printed products made of Gr1 have low strength, which is not suitable for high-load and pressure-bearing structural components; therefore, we suggest that if high strength is required, the Gr2 grade titanium wire should be chosen as the priority, and for components requiring higher strength, the Gr5 (TC4) grade titanium wire should be selected.

 

2. Please note that the commonly referred to ordinary welding Gr1 wire is not equivalent to the additive manufacturing-specific TA1G wire. This is because the additive manufacturing-specific titanium wire has higher requirements for the content of gases in the material, as well as the surface roughness and wire diameter tolerance of the material, and the absence of skin inclusion and other impurities; however, the commonly referred to ASTM B863 welding wire can be used as a temporary sample material, but if batch production is required, we recommend purchasing the additive-level TA1G wire material.

 

3. The protection requirements are extremely high: the molten titanium is highly prone to absorbing hydrogen, oxygen, and nitrogen. WAAM/DED must be protected by high-purity argon gas. Insufficient protection will result in embrittlement, pores, and yellowing.

 

4. The medium restrictions remain unchanged: the Gr1 printed parts are still not resistant to hydrofluoric acid, fluorine-containing media, and high-temperature strong alkalis.

 

5. Do not confuse: the SLM powder machine usually uses Gr1 titanium powder; the 3D printing machine using titanium wire for filament extrusion uses Gr1 titanium wire.

How To Cooperate With Us?

Contact person :Tracy Zhang 

Our address

Baoji city, shaanxi province,China 

Phone Number

0086-18291730106

modular-1

 

 

Hot Tags: gr1 titanium wires, China gr1 titanium wires manufacturers, suppliers, factory, Gr2 Titanium Sheet, Gr5 Titanium Strip, Gr7 Titanium Strip, Pure Titanium Welding Wire, titanium wire

Send Inquiry