3D printed titanium wire

Additive manufacturing titanium wire (WAAM / DED wire feeding 3D printed titanium wire)
National standard: GB/T 43302-2023 "Additive Manufacturing Titanium and Titanium Alloy Wire Materials", specifically for arc additive WAAM and laser directed energy deposition DED; different from ordinary argon arc welding wire and SLM titanium powder used in powder bed.
Common corresponding grades: AWS A5.16 ER Ti5 (TC4 Gr5), AMS 4951, ASTM F136 (TC4 ELI Gr23 )
Physical basic parameters
TC4 / TC4 ELI density is approximately 4.43 g/cm³;
TA1/TA2 pure titanium density is approximately 4.51 g/cm³;
TA15 density is approximately 4.45 g/cm³
Elastic modulus of TC4 is approximately 110 GPa;
pure titanium Gr2's elastic modulus ≈ 105 GPa
• Melting point of titanium is 1640~1668℃
• Titanium is non-magnetic and has a low linear expansion coefficient; its thermal conductivity is poor, so during printing, there is a large heat accumulation, and cooling and argon gas protection during printing are necessary.
Titanium molten pool at high temperature (>400℃) easily absorbs O, N, H, directly becoming brittle and generating pores, so high-purity argon gas protection must be maintained throughout WAAM/DED

Chemical composition (wt%, GB/T43302)
| TC4 (Gr5) | Ti: excess; Al: 5.5~6.75; V: 3.5~4.5,Upper limit of impurities: C≤0.08, Fe≤0.30, O≤0.19, N≤0.05, H≤0.015; other single elements≤0.10, total≤0.30 National standard information... Aerospace high-end orders often require O≤0.15, H≤0.008 to reduce brittleness and porosity risks after printing |
| TC4 ELI (Gr23, medical additive) | Al: 5.5~6.5; V: 3.5~4.5 Strict control of gap: O≤0.13, N≤0.03, H≤0.008, impurities are much stricter than ordinary TC4, used for implant additive |
| TA2G (Gr2 pure titanium additive wire) | Ti excess; C≤0.08, Fe≤0.30, O≤0.24, N≤0.03, H≤0.015 National standard information... |
| TA15 | Ti excess; Al: 5.5~7.0; Zr: 1.5~2.5; Mo: 0.5~2.0; V: 0.8~2.5; Fe≤0.25, O≤0.15, H≤0.015 |
comparison of Different Grades 3D printed titanium wire
| Grade | National Standard Code | Corresponding to American Standard | Main Application |
| TC4 (Ti-6Al-4V) | TC4 | Gr5 / ER Ti5 | Aerospace structural components, tooling, racing cars, marine load-bearing parts. WAAM is the most commonly used |
| TC4 ELI | TC4ELI | Gr23 | Medical implant additive manufacturing, high fatigue components; ultra-low gap O/N/H, better toughness |
| TA1G / TA2G (Industrial Pure Titanium) | TA1G / TA2G | Gr1 / Gr2 | Anti-corrosion components, marine chemical engineering, extracorporeal medical devices (non-implantable parts), good plasticity, resistant to chloride ion corrosion |
| TA15 | TA15 | Near α titanium alloy | Aerospace medium-temperature components (≤ 500℃), casing, high-temperature supports, with low crack sensitivity |
Surface, shape, tolerance (the biggest difference between additive wire and ordinary welding wire)
1. Diameter tolerance of titanium wire for 3D printing is usually within ±0.05mm; in high-precision orders, it can be achieved within ±0.02mm according to special requirements; please note that the tolerance difference of titanium wire will cause unstable wire feeding, fluctuation of the molten pool, and uneven layer thickness.
2. Surface roughness of titanium wire is usually Ra ≤0.8 μm (mainstream), but for aerospace/medical work environments, Ra≤0.4μm can be required, but the cost will increase.
3. Surface requirements
◦ Not allowed: scratches, peeling, pits, oxidation color, oil stains, graphite lubricant residue, iron contamination; surface defects will induce pores, poor fusion
◦ Conventional surface: vacuum annealing bright drawing surface (Bright drawn), preferred; acid-washed surface is generally not recommended for additive, prone to residual oxidation inclusions
◦ Medical TC4 ELI additive wire: add ultrasonic degreasing cleaning, dust-free packaging, strictly control surface contaminants
4. Straightness: ≤3 mm/m, ensure smooth wire feeding; neatly wound, no knot, no local hard bends; no solder joints are allowed in the coil (national standard mandatory) National standard information...
5. Non-destructive: The finished filament is subjected to ultrasonic flaw detection, grade A1, to avoid internal inclusions and cracks.
Mechanics (The mechanical properties of the wire material in the annealed state, the mechanical properties of the printed finished product will vary with the process)
• TC4 wire: Rm ≥ 895 MPa, Rp0.2 ≥ 827 MPa, elongation ≥ 10%
• TC4 ELI: The strength is slightly lower, the elongation is higher, the toughness and fatigue are better
• TA2G pure titanium wire: Rm ≥ 345 MPa, Rp0.2 ≥ 275 MPa, elongation ≥ 20%, good plasticity
• TA15: Rm ≥ 957 MPa, suitable for high-load bearing
Note: The mechanical properties of the wire material itself ≠ the mechanical properties of the printed part; WAAM deposited state usually requires subsequent stress relief annealing, and aerospace parts also need heat treatment
Points to note when selecting additive titanium wires:
1. Ordinary aerospace structural WAAM → TC4 Gr5 (the most cost-effective)
2. 3D printing implant prostheses, orthopedic parts, high-fatigue parts → TC4 ELI Gr23 (ASTM F136), cannot be replaced by ordinary TC4
3. Corrosion-resistant, seawater, chemical additive parts: select grade TA2G Gr2; those requiring excellent cold forming can choose TA1G Gr1
4. Aerospace components at 500°C or above: recommend selecting TA15
5. Be careful not to confuse this point; that is, additive wires are not the same as ordinary titanium welding wires; ordinary welding wires have more relaxed requirements for oxygen, surface, flaw detection, and coil winding; if choosing ordinary welding wires, then after being put on the machine, there is a tendency to have pores and broken wires.
6. Customers ask about medical devices: TC4 ELI wire is only the raw material, the final implanted part also depends on ISO10993 biocompatibility
Contact person : Tracy
Our address
Baoji city, shaanxi province ,China
Phone Number/ Whatsapp
+86-18291730106

Hot Tags: 3d printed titanium wire, China 3d printed titanium wire manufacturers, suppliers, factory, Gr2 Titanium Sheet, Gr5 Titanium Strip, Gr7 Titanium Strip


